Animal Surgical Devices
Instech Swivel clamp for MINF tethers
The Instech MCLAMP is a replacement swivel clamp specifically designed for use with the MINF mouse head block tether system. It allows for the direct attachment of the fine wire tether to the outlet tube of low-torque swivels, ensuring efficient torque transmission as the animal moves.
Features
- Type: Slotted swivel clamp
- Application: Connects the MINF wire tether to a fluid swivel
- Compatibility: Designed for use with Instech low-torque swivels, such as models 375/25 or 375/D/22QM
- Function: Facilitates the use of lightweight .010" diameter looped wire tethers instead of traditional spring tethers
- Packaging: Typically sold in packages of 5
Med Vet International 12mm x 28mm Titanium TTA Cage, J1072MCT
TTA (Tibial Tuberosity Advancement) CagesTitaniumCage 12 x 28mm 2.4mm screw
Med Vet International Cancellous Screws 3.5mm x 32mm, J0423L, 6 Pack
3.5mm Cancellous Screw. 1.75 Pitch. The coarser thread has a much bigger "bite" into the bone. Use on metaphyseal or other cancellous bone. The screw needs its own tap. (JOR409c)
Med Vet International Self Tapping Screw, J0404D, 2.7mm x 19mm, 6 Count
For use with 2.7mm (7/64") round-hole plates in small- to medium-sized patients. 6/pk.
Med Vet International Self Tapping Screw, J0404E, 2.7mm x 22mm, 6 Count
For use with 2.7mm (7/64") round-hole plates in small- to medium-sized patients. 6/pk.
Med Vet International Locking Screw 2.7mm x 16mm, J1133TF, Each
Locking Screw 2.7mm x 16mm, J1133TF, Each
Med Vet International Periosteal Elevator, 180mm, (7 1/2"), Curved 6mm tip, J0226S
A popular configuration available in 6mm curved tip. Lightweight fiber handle.
Med Vet International Endotracheal Tube Adapter 10.5mm, J0157KK
Portex Endotracheal Adaptor The full range of small animal endotracheal tubes is covered by the twelve adaptors. The adaptors may be sterilized by conventional methods. The compact Swivel Connector may be rotated a full 360 degrees affording maximum positioning and flexibility. For use on all endotracheal tubes.
Med Vet International Endotracheal Tube Adapter 4.0mm, J0157B
Portex Endotracheal Adaptor The full range of small animal endotracheal tubes is covered by the twelve adaptors. The adaptors may be sterilized by conventional methods. The compact Swivel Connector may be rotated a full 360 degrees affording maximum positioning and flexibility. For use on all endotracheal tubes.
Med Vet International Humidification Management Exchanger, over 75 lbs, J0606B, 5 Pack
In human anesthesia the prevention of moisture andheat loss is a critical consideration. The smaller patientis especially a concern because hypothermia is more likely to occur. Humidification management exchangers are routinely used in human anesthesia. Veterinarians are starting to recognize the value of these products andmake them part of their anesthetic regime.The Humid-Vent is a compact connector that is a heat and moisture exchanger. They are placed in the breathing circuit between the "Y" piece (or "T" piece for non-rebreathing) and the endotracheal tube. Inside the connector is a special medium consisting of hygroscopic, naturally absorbent microwell paper. The Humid-Vent can be used up to 24 hours. After 24 hours they lose their effectiveness and must be replaced. In veterinary use they are typically replaced weekly. 5/box.
Med Vet International Locking Plug for TPLO Locking Screw, J0438P
Used to protect locking holes while contouring plate
Med Vet International 2.4mm x 20mm Titanium Cortical Self Tapping Screws, J1073FT, 6-Pack
Many fractures in feline and small canine patients are too small for the 2.0mm DCP and the 2.7mm CDP is too large.The difference between these plates is enormous compared to the difference between 2.7 and 3.5 CDPs. The AMI (resistance to bending) of the 2.7 CDP is 20 times stiffer than the 2.0 DCP. The AMI of the 2.4 DCP is 10 times that of the 2.0 DCP.The solution is a 2.4 series of plates and screws. The plates in both size and strength are midway between 2.0 and 2.7 DCPs. The range and specifications are shown below. The standard 1.5mm hex screwdriver (used for 1.5 and 2.0 screws) is required. The pilot drill is 1.8mm and dedicated instrumentation such as load/neutral guides are also available.